Download Article

Download Article

PUR has multiple products available for filtering water, but the filters become less effective over time as they fill with contaminants. How you supervene upon the filter depends on which system yous're using. If yous have a plastic pitcher or dispenser yous proceed in the refrigerator, soak the new filter before screwing it in. For filtration systems that attach to your sink faucet, just remove the old filter then you tin put the new ane in its place. When yous're finished, you'll take clean water to drink for some other few months!

  1. i

    Soak the replacement filter in common cold water for 15 minutes. Identify the new filter in a clean container that's deep enough and then you lot tin can fully submerge it. Fill the container with cold water and leave it alone for at least 15 minutes. During this time, any excess carbon from the filter will lift out and split so it doesn't get in your drinking water.[ane]

    • Soaking the filter also ensures that water flows evenly when you use it.
    • Don't use water warmer than 86 °F (thirty °C) since it could damage the filter.

    Warning: Avoid using tertiary-political party filters with your PUR pitcher or dispenser since they may non fit as well or take been tested equally efficiently.

  2. 2

    Twist the old filter counterclockwise to remove it. Take the chapeau off of the pitcher or dispenser and set it aside. So, elevator up the pour tray, which is the blue plastic reservoir on top, and take information technology out. Catch the cylindrical filter from the bottom and rotate it counterclockwise then it unhooks from the filter. Pull the sometime filter out through the pinnacle of the pour tray and throw in the garbage.[2]

    • Wait until the pour tray is empty to modify your filter, or else it may be difficult to remove or you lot may spill.

    Advertizing

  3. three

    Rinse the new filter nether your faucet for 10 seconds. Accept the filter out of the container when it's finished soaking and agree it underneath your faucet. Turn on cold water and rotate the filter so you can rinse it off completely. Later on ten seconds, plow off the water and shake out whatever excess that's nevertheless in the filter.[three]

    • Don't utilize hot h2o to rinse the filter off, or else y'all may damage information technology.

  4. 4

    Screw the filter clockwise into the pour tray to secure information technology. Slide the long, cylindrical role of the filter through the hole in the middle of the pour tray and push it downward equally far every bit it goes. Hold the filter by the bottom and rotate information technology clockwise until you hear it click into place. Try tapping on the end of the filter to make sure information technology doesn't popular out from the pour tray. Place the pour tray dorsum into the pitcher or dispenser before replacing the lid.[4]

    • If the filter does pop out of the pour tray, and then you didn't properly secure it. Reinsert it and endeavour turning information technology clockwise once again.
    • PUR filters for pitchers and dispensers usually work for 40 gallons (150 50), or approximately 2 months.

  5. five

    Hold the Reset button down for 5 seconds if your pitcher or dispenser has one. Some newer PUR pitchers and dispensers take sensors that detect when yous need to replace the filter. Correct after you supervene upon the filter, press the Reset button on the lid and go on it held down for 5 seconds. A green lite will blink on the chapeau once the sensor resets.[five]

    • Older pitchers or dispensers may non accept an electronic brandish.

    6. Advertisement

  1. 1

    Unscrew the filtration system from your faucet. Support the weight of the filtration system with your nondominant paw so it doesn't fall and interruption. Rotate the plastic locking nut holding the filtration system to the faucet counterclockwise to loosen it. Once you unscrew the arrangement completely, carefully lift it away from the faucet and set it downwardly on a countertop or towel.[6]

    • H2o may spill out from the faucet when y'all unscrew the filtration organization.
    • Some models of PUR filtration systems may snap onto the faucet. If information technology doesn't unscrew, try pulling it straight down from the faucet.

  2. two

    Twist open up the top cover of the system to remove the former filter. Hold the filtration organization so the rounded end of the large cylinder points up. Unscrew the peak from the cylinder by rotating information technology counterclockwise, and gear up the comprehend aside. Pull the quondam filter straight out from the system and throw it abroad in your trash.[vii]

    • The top cover is always on the opposite stop of the spout that dispenses water.

  3. 3

    Set up the new filter inside of the system and screw on the cover. Make sure the narrower end of the filter is on the bottom and the logo is right-side up. Place the filter into the filtration system and then information technology has a loose fit. Ready the pinnacle cover back over the filter and spiral information technology into place to secure information technology.[8]

  4. 4

    Reattach the filtration system to your faucet. Agree the filtration system confronting the bottom of the faucet and so the threadings are perfectly horizontal, or else they won't form a tight seal. Rotate the locking nut clockwise onto the faucet and continue tightening it until information technology's hand-tight. Turn on the water and make sure it doesn't drip or leak at the seam.[9]

    • If your filtration system doesn't screw on, line information technology upward with the faucet and apply firm pressure to snap it on.

  5. 5

    Run cold water through the filtration system for 5 minutes. Plow the handle on the correct side of the filtration system to divert the water through the filter. Let the h2o to run through the filter for five minutes to get rid of whatever residue inside so information technology works more efficiently. After that, you can utilise the filter immediately later on turning information technology on.[10]

    • PUR faucet filters work for 100 gallons (380 L) of water, or about iii months of use.
    • Don't run water over 100 °F (38 °C) through the filter since you could damage information technology.

    Alarm: The water may sputter or look cloudy when you showtime use the new filter, merely it will get meliorate equally y'all run water through information technology.

    6. Advertisement

Ask a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertisement

  • Many PUR filtration systems accept electronic lights that detect when you demand to modify your filter. If y'all see a green light flash, yous don't demand to change your filter. If it blinks yellow or red, then yous need to supercede the filter soon.[11]

Thank you for submitting a tip for review!

Advertisement

  • Don't use h2o that's in a higher place 82 °F (28 °C) in a pitcher or over 100 °F (38 °C) through a faucet since information technology can damage the filter.[12]

  • Only use the filter with water that'due south already safe to beverage since it will non remove bacteria or infection.[13]

Advert

References

About This Commodity

Thanks to all authors for creating a page that has been read 46,668 times.

Did this article help you?