How To Set Up Free To Air Satellite
-
i
-
two
Make sure that you tin can receive your satellite's signal. Before attempting to set up an FTA organization, you should know if it's possible for yous to receive your selected satellite's bespeak. You tin test this by going to http://www.dishpointer.com/ and doing the following:
- Blazon your city and country (e.g., "Palo Alto, California") into the "Your location" text box on the left side of the page.
- Select your satellite's proper noun from the drop-down box on the right side of the page.
- Click Search!
- Brand sure that there is a green line indicating line-of-sight for your satellite. If this line is ruddy, the satellite won't work properly in your area.
Advertisement
-
3
Note the network'southward bearings. In the pop-up box on the map, wait at both the "Superlative" number and the "Azimuth (true)" number. Y'all'll utilize these numbers (in degrees) to adjust your dish after.
-
4
Ensure that you have the proper hardware. You lot'll need the following equipment before you tin can actually install the satellite dish:[i]
- Satellite dish — Used to receive the satellite's signal. You lot'll need an viii-human foot dish for C-band channels or a 35-inch dish for KU-band channels.
- Satellite receiver — Used to receive the satellite dish's input and translate information technology into channels for your Television set.
- Satellite tuner — Used to fine-tune the satellite dish's position.
- HDTV — Necessary for well-nigh FTA systems, as the receiver will generally require an HDMI input on the Television itself.
- Coaxial cable — Unremarkably packaged with the satellite dish, simply you may demand to buy a longer or shorter cablevision depending on your satellite dish'southward location.
-
5
Make up one's mind your satellite dish's optimal position. You'll desire to aim your satellite dish at the satellite itself, and then find a high location (e.m., a rooftop or a balcony) from which the dish tin face up the satellite without losing rails of the satellite's bearings.
- You'll also demand to ensure that your satellite dish isn't obstructed past trees, buildings, or other obstacles.
-
half-dozen
Figure out the best route from your dish to your Idiot box. Since yous'll need to run a coaxial cable from the dish to the receiver within your house, you'll want to find a path that minimizes the cable'south exposure to the elements while keeping the cable every bit short as possible.
- Many dish users route the cable along the side of the house and through a wall where necessary, but your cable setup may vary.
- If necessary, purchase a new coaxial cable that volition reach your dish from the receiver earlier proceeding.
Advertisement
-
1
Secure the dish in your selected position. Place the dish's mast and dish itself on a stable surface, then lock down its position using the included bolts or fasteners.
- It's incredibly of import to brand certain that the dish is secured as tightly as possible so that information technology doesn't become loose during a windstorm.
- If the dish is mounted on a wood roof, you lot can caulk effectually the base of operations to make it waterproof.
-
two
Indicate the dish toward your satellite. Using the "Elevation" and "Azimuth" numbers every bit guides, bending your satellite dish toward the satellite that you lot want to use. This will ensure that the dish is roughly positioned toward the satellite.
- You'll about probable need a compass for this pace.
-
3
Connect the satellite tuner. Using the 6 human foot (1.viii m)-long coaxial cable on your satellite, plug in the satellite tuner.
-
iv
Use the satellite tuner to fine-tune your dish's horizontal axis. Turn on the satellite finder, input the satellite name or select it from a listing, and enter the satellite's frequency. You lot should hear a continuous beeping audio which volition allow you to approve your dish's position:
- Rotate the dish left or right.
- Listen for quicker beeping to ensure that y'all're rotating the dish in the correct direction.
- Rotate the dish the other mode if the spaces between beeps become longer.
-
5
Secure your dish's horizontal axis. Tighten the rotation control screw completely to fix this angle.
-
vi
Adjust the vertical axis. You'll practise this in the same manner every bit you adapted the horizontal axis; in one case the beeping is as quick as you can manage to achieve, you lot can tighten the vertical axis screw.
-
vii
Connect your satellite dish to your receiver. You lot'll utilise the long coaxial cable for this stride. The coaxial cable should plug into the back of the satellite dish's receiver.
- You can use a staple gun to staple the coaxial cable to your house'south siding in gild to forbid information technology from hanging freely.
- Depending on your firm's layout, you may need to drill a hole in the wall in order to thread your coaxial cable through to the receiver. If so, make certain not to drill through any pipes or wires.
Advertisement
-
1
Plug the receiver into both a power source and your TV. Once you've attached the coaxial cable to the receiver, you tin employ the receiver's HDMI cable to adhere to one of your TV'south HDMI ports.
- You'll too need to use the receiver'south power cable to connect to an electric outlet.
-
2
Turn on the receiver if necessary. Your receiver should turn on when plugged in, but there may be an On/Off switch on the side or the dorsum of the receiver. If and then, flip the switch to the "On" position before proceeding.
-
3
Switch to the receiver'southward channel. Turn on your TV, then switch to the HDMI input into which you plugged the receiver.
- For example, if you plugged your receiver into the "HDMI 1" slot, you'll switch the input to the "HDMI one" channel using your TV's Input or Video menu.
-
4
Let the receiver to perform its installation if necessary. Some receivers will go through an automatic setup process the start time they're turned on; if so, allow your receiver to complete the setup before continuing.
- If prompted to perform any actions during the setup, follow the on-screen instructions.
-
five
Open the receiver's card. On your receiver's remote, find and press the Carte du jour button. You should see a popular-up menu appear on-screen.
-
vi
Observe your dish's antenna setup card. You'll usually have to use your remote'south arrow buttons to discover the "Install" or "Dish" choice, but consult your receiver's manual if you tin can't find the setup section of the menu.
-
7
Select a satellite. In the "Satellite" department of the carte, utilise the arrows to scroll left or right until you find your satellite's proper name.
-
8
Select an LNB frequency. In the "LNB" department of the carte du jour, use the arrows to select 10750 as the LNB number. This is the near commonly used LNB frequency for satellite networks.[two]
- If y'all're using a C-band network, you'll select 5150 here instead.
-
9
Scan for channels. Find the "Browse" or "Single Satellite Scan" department of the menu, set the "FTA Only" section to Yes if possible, and start the browse by selecting Yes, OK, or Offset. Your dish will begin searching for available satellite TV channels; in one case it finishes, you'll be able to watch Television set like usual on your dish's channel.
Advertisement
Add New Question
-
Question
How do I decide which management to aim my satellite dish?
Find a satellite dish-pointing app for your smartphone. Or search for a satellite-pointing website online that can help you with elevation and azimuth numbers for your specific location. (Make sure y'all take a compass on hand for this method).
-
Question
What are the settings for satellite info. for free to air in Nigeria?
If you become to an FTA site, such as Lyngsat, you'll come across the settings for NTA international on 97W.
-
Question
Tin can I watch channels from India?
Yep, if yous are in Asia, you tin can watch them on Satellite Asia saturday vii@105°. But virtually Indian channels are FTA.
-
Question
My receiver is an SM 2350 Power Tech high-definition satellite receiver. When I install my receiver, the electricity on it stops working. What should I do?
If the receiver has an electric adapter, you lot need to by a new 1; the adapter has a short or is damaged.
-
Question
How do I watch programs on my satellite without a subscription?
The channels are not what you typically receive by cablevision or pay satellite. These are special-interest channels of a religious, cultural or educational nature. You demand a legal FTA box or computer menu, satellite dish and LNB for FTA service, as a minimum.
-
Question
What satellite channel has Tv set programs coming from Ethiopia?
There currently are several channels from Ethiopia on 97W, but FTA channels come up and go regularly.
-
Question
Tin I add together a satellite if it doesn't appear on my complimentary to air receiver?
Yes. Depending on your receiver, information technology may exist every bit like shooting fish in a barrel every bit opening the settings menu and entering the data for the new satellite.
-
Question
Can I connect a FTA ready pinnacle box with Tata Sky dish?
The dish has nil to do with the box and signal strength. All you demand is a good position of your dish and proficient settings on your FTA set meridian box and it will work in sync.
-
Question
What satellite should I target to receive tv programs from Puerto Rico?
There is null I'm aware of on Ku-band (the dish this ready-up describes) from Puerto Rico. If you had a 6 to 12 foot "large" dish, then you lot could try 99W.
-
Question
How do I notice what channels are available in my abode town?
Depends on what satellite y'all want. Get to LyngSat and find the satellite you want, it lists all the channels available.
Prove more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertizement
Near This Article
Article Summary X
one. Select a network.
two. Make sure you can receive your satellite'southward betoken.
3. Install the receiver dish.
4. Signal the dish toward your satellite.
5. Install the tuner and adjust the axes.
6. Connect the dish to the receiver.
7. Connect the receiver to your TV.
8. Search for channels.
Did this summary help you?
Thanks to all authors for creating a page that has been read 931,584 times.
Is this article upward to engagement?
How To Set Up Free To Air Satellite,
Source: https://www.wikihow.com/Install-and-Set-Up-Free-to-Air-Satellite-TV-Program-Receiver-System
Posted by: maronepaide1972.blogspot.com
0 Response to "How To Set Up Free To Air Satellite"
Post a Comment